I Built My Own Easy DIY Console Table For Under $35

I built my own Easy DIY Console Table for under $35

When you buy through links on my website, I may earn a commission.

Console tables are great for entryways, foyers, behind couches and underutilized spaces in a room. They can be pricey or you can be like me and build your own Easy DIY Console Table for under $35! Yup, that’s right… UNDER $35 (minus the tools!)

I’m not a professional carpenter or furniture-maker so I don’t have any fancy “plans” for this easy DIY console table which speaks on how easy this project is (because my furniture-making skills are slim!)


Watch the YouTube video here: Build your own Easy DIY Console Table for under $35

For this easy DIY Console Table, you will need the following:


  • 5 wood boards:
    1. • 2 boards: 12-in x 3-ft Smooth Natural Spruce Wood Wall Panel (front and back)


    1. • 3 boards:1-in x 8-in x 4-ft; Actual: 0.75-in x 7.25-in x 4-ft) Whitewood Board


  • Power drill
  • Drill bit set
  • Mini Circular Saw
  • Wood Screws (hillman flat phillips #8×2)
  • Sanding block
  • Triangle Measuring Tool (or use measuring tape!)
  • Wood Glue (optional)
  • Paint:

    rustoleum wood stain antique white

      1. (If you want to stain the wood)
        1. • kilz complete coat paint (what I painted with)

    Wood paint sealer

  • Pieces for the table
    Make sure 2 of the pieces are longer than the table legs as these will be your front and back pieces!

    Table Top Directions

    First, I measured how big I wanted my console top with measuring tape. I know exactly where this console is going (in a corner in my office). Once I have my line marked, I cut with my Mini Circular Saw.

    I am seriously kicking myself for waiting so long to purchase a circular saw. It’s LEGIT. It’s the right size for someone like me who isn’t that great with tools, it has 3 different blades and a laser to ensure I’m cutting a straight line. I absolutely cannot wait to use this for some more projects (I already have my DIY projects on Pinterest for it! lol).

    Once you’ve cut your console top to its desired length, go ahead and sand it out so it’s smooth!

    Table Legs Directions

    You want to, first, predrill holes inside of the legs before drilling in your screws!

    Trust me on this! If you predrill your holes first, this guarantees your screw won’t break off into the wood and that your wood won’t crack. I recommend making the predrill hole (pilot hole) slightly smaller than the actual screw size.

    Every project I do, I use my power drill. It was my “first-time homeowner” gift to myself and I use it often! I decided to purchase a new electric power drill bit set since I use my drill so much!

    You first want to measure where you want the screws. I recommend at least an inch out so your wood doesn’t crack off. Be sure to save those measurements where the predrilled holes are (pilot holes) as you will need those measurements to drill inside the table console!

    I went ahead and added wood glue after I predrilled my holes since this adds an extra level of protection since I won’t be using table brackets!

    I recommend applying the glue to the table top upside down. It’s much easer.

    TIP Be sure to wipe off any excess wood glue! You do not want it to dry on the wood because it’s going to be super hard to paint on top of it and damn near impossible to stain the wood if there’s wood glue all over it!

    Allow the glue to dry for about 30 minutes before going in with the screws.

    Take out the measurements where your pilot holes are and measure/mark that on your tabletop. Drill and add the screws on each side.

    Front & Back boards

    I have no idea why but this was the fun part for me (maybe because I got to use my mini circular saw and feel like Bob Bre the Builder.

    Lay your table down and then lay your front piece on top. I measured where I needed to cut and went through twice with my saw. You’ll want to do this with both ends of the board and for both boards (the front board and the backboard).

    I promise this part isn’t nearly as hard as it sounds! If you can measure, you can definitely do this easy DIY console table!

    This was my progress so far:
     Easy DIY Console Table for under $35

    So far so good? I was proud lol.


    I hate painting furniture. I love painting canvases but when it comes to painting rooms and furniture, I’m super messy and ehhh, just not that great at it.

    Originally, I planned to stain this table antique white but I wasn’t feeling it after a few strokes and decided to just paint it white.

    I did two coats and let it dry overnight. The next day, I used a wood paint sealer which is extremely important! Usually, when you paint furniture with latex paint, you need to protect the finish with a sealer or topcoat. This will prevent it from chipping and peeling. I used a glossy finish because I want my table to shine as bright as my future (and that’s bright!)?

    ANDDDDDDD…… We’re done!

    How did I do? Did I do a good job? I plan to use this table in my office/ Youtube Filming studio! You can build your own easy DIY console cable for under $35 because well, I just did! It’s sturdy, cute and I can’t wait to decorate it!

    Watch the YouTube video here: Build your own Easy DIY Console Table for under $35

    Do you love decorating your home on a budget?
    If so,then you’ll love my FREE guide all about affordable decorating! This guide includes tips, an extensive decor checklist, video resources to decorate & more!

    Get instant access to my FREE guide by entering your info in below!

    The form you have selected does not exist.


    PIN TO YOUR PINTEREST BOARD: Build your own Easy DIY Console Table for under $35

    Build your own Easy DIY Console Table for under $35

Leave a Comment